Hardwood flooring
Explore species, plank character, finish direction, and installation conditions with a flooring specialist.

Questions to resolve
Choose for the conditions, not only the color.
- What is under the floor? Identify concrete, plywood, or an existing covering before choosing a plank. The installation plan needs to address the actual substrate and the selected manufacturer's requirements.
- Which rooms connect? Compare samples in your home's daylight and alongside cabinets, then plan doorway heights, stair details, and transitions to adjoining floors before ordering.
- Will you want to refinish later? Ask for the product's construction and refinishing guidance. A wood appearance alone does not establish how much sanding a floor can tolerate.
Manufacturer, collection, dimensions, availability, and price are confirmed only from current product documentation and a project-specific conversation.
The short answer
Solid hardwood installed in San Diego runs from $8 to about $18 per square foot in Swell's 2026 planning range, material and labor, before removal and subfloor prep. It suits homes with a wood subfloor and owners who want a floor that can be refinished for decades. Over a concrete slab, engineered wood is the usual route.
- Installed planning range
- $8 to about $18 per sq ft (Swell's 2026 San Diego planning range); premium species, wide planks and heavy prep run higher
- Removal and prep
- Old floor removal $1.50 to $5 per sq ft; subfloor leveling or repair $2 to $5 per sq ft (San Diego market guides, 2026)
- Best for
- Raised-foundation homes with a plywood or plank subfloor; living areas, bedrooms, halls and stairs
- Watch out for
- Concrete slabs, bathrooms and laundry rooms, radiant heat without the manufacturer's approval, and HOA sound rules in upper-floor condos
- Refinish later
- Yes. Screen and recoat $2 to $4 per sq ft; full sand and refinish $4 to $9 per sq ft (Swell planning ranges)
- Next step
- Free in-home measurement by Tidal Flooring, CSLB C-15 #1002910, before any written price
What solid hardwood is and how it is built
A solid hardwood plank is one piece of wood from top to bottom, usually about 3/4 inch thick, milled with a tongue on one edge and a groove on the other. It is nailed or stapled through the tongue into a wood subfloor. Because the whole plank is wood, it can be refinished many times.
Planks come prefinished, with the stain and finish applied at the factory, or unfinished for sanding and finishing in your home. Prefinished floors install faster and have a harder factory coat. Site-finished floors have no bevels between boards, take any custom stain, and are the usual way to blend new wood into an older floor. Species sets the look and the hardness; the sample in your own light decides.
Where it works in San Diego homes
Homes built from the 1920s through the 1950s in Point Loma, North Park, Coronado and Mission Hills often sit on a raised foundation with a wood subfloor, many with original oak or fir still under carpet. These are the natural homes for solid hardwood: new planks nail over the existing subfloor or lace into the original floor so the repair disappears after sanding.
Most San Diego homes built after the 1960s, and nearly every ADU and garage conversion, sit on a concrete slab. Solid hardwood cannot be nailed to concrete. The options are a plywood subfloor built over the slab, which raises the floor and the cost, or an engineered or luxury vinyl floor that glues or floats directly on the concrete. Our measurement visit identifies the slab before you fall in love with a plank.
Coastal humidity in La Jolla, Del Mar and Encinitas is mild by national standards, but marine air and open sliders move moisture through a house all day, and wood swells and shrinks across the grain in response. Acclimation per the manufacturer, the specified expansion gap, and narrower boards in the most exposed rooms keep seasonal gaps small.
Upper-floor condos add two problems: a concrete subfloor, and an HOA that usually requires a tested sound rating and an approval letter before any hard floor goes in. Solid nail-down hardwood rarely fits both; the engineered wood page covers the floor that usually does.
What it costs in San Diego in 2026
Swell's planning range for solid hardwood installed is $8 to about $18 per square foot, material and labor together. San Diego and Southern California guides published in 2026 land in the same band, with oak near the low end, walnut and other premium species toward the top, and figures above $20 per square foot for exotic species or extensive prep.
The range is before removal and prep: San Diego guides put old floor removal at $1.50 to $5 per square foot and subfloor leveling or repair at $2 to $5. Stairs and transitions are priced per piece, and herringbone or chevron patterns add labor because every board is cut and fitted.
The number that matters is the one in your written estimate after a measurement visit. Related reading: the hardwood installation cost guide at /learning-center/hardwood-floor-installation-cost-san-diego.
Installation and prep
Every job starts with the subfloor: flatness checked, loose areas fastened, moisture tested in the subfloor and the planks against the manufacturer's limits. Planks then acclimate in the rooms where they will live for the time the manufacturer specifies, not a fixed number of days copied from a brochure.
Boards are nailed or stapled through the tongue, with the expansion gap held at the walls and later covered by base shoe or baseboard. Prefinished floors are ready for furniture when the trim is done.
Site-finished floors are sanded with dust-contained equipment, stained if you want a color, and coated. With Bona Traffic HD, a waterborne finish we use often, the manufacturer's data sheet gives 2 to 3 hours of drying per coat, light foot traffic after 24 hours, about 80 percent cure at one day and full cure at three days, with rugs kept off until full cure. High humidity and cool temperatures stretch those times.
Care, lifespan and the honest downsides
A solid hardwood floor outlasts the finish on it. When the surface dulls but the finish is intact, a screen and recoat at $2 to $4 per square foot in Swell's planning range brings it back. When wear reaches bare wood or you want a new color, a full sand and refinish at $4 to $9 per square foot does it; San Diego guides put that at 3 to 5 days.
The downsides are real. Water is the enemy: a slow leak under a dishwasher or a wet laundry room will cup and stain boards, which is why we steer hardwood away from bathrooms and laundry rooms. Dogs' nails and dropped pans mark softer species and glossier finishes more than matte finishes on oak. Solid hardwood also costs more installed than vinyl and cannot go straight onto a slab.
How Tidal Flooring installs it
Tidal Flooring is the flooring division of Swell Contracting and holds its own CSLB C-15 flooring license, #1002910. Every job runs the same way: a free in-home measurement first, samples compared in your light next to your cabinets and trim, then a written scope with removal, prep, material, installation method, trim and stairs as separate lines.
Install dates and material lead times are written into that scope for your job rather than quoted here, because they depend on the product and the season. Call (619) 403-3662 or request a measurement to start.
Hardwood flooring questions
How much does hardwood flooring installation cost in San Diego?
Swell's 2026 planning range for solid hardwood installed is $8 to about $18 per square foot, material and labor together, before removal and subfloor prep. Add $1.50 to $5 per square foot to remove the old floor and $2 to $5 for leveling or repair when the subfloor needs it, per San Diego market guides. Your written estimate follows a free measurement.
Can hardwood be installed over a concrete slab?
Solid nail-down hardwood cannot be fastened to concrete. Over a slab you either build a plywood subfloor on top, which raises the floor height and the price, or choose an engineered wood or luxury vinyl floor designed to glue or float on concrete. Slab moisture is tested either way, because wood over a damp slab fails whatever the construction.
How long does hardwood installation take, and when can I put furniture back?
The crew time depends on square footage, prep and whether the floor is prefinished or site-finished, so it is written into your scope rather than quoted here. Prefinished floors take furniture when trim is done. Site-finished floors coated with Bona Traffic HD take light foot traffic after 24 hours and are fully cured at three days, per the manufacturer; rugs wait until full cure.
Do hardwood floors need to acclimate, and for how long?
Yes. Planks need to reach moisture balance with your home before installation, and the duration is set by the manufacturer's instructions and by moisture readings of the planks and the subfloor, not by a fixed rule. In coastal San Diego homes with open sliders this step matters more than inland. Skipping it is the usual cause of gaps and cupping in the first year.
Can new hardwood match my existing floors?
Usually, if the existing floor is solid wood. New unfinished boards of the same species and width are laced into the old floor, then the whole area is sanded and finished together so the color and sheen match. Matching a prefinished floor board for board is harder because factory colors change, so we often refinish the whole room instead. Bring a loose board or a photo to the measurement.
Is hardwood a good choice for a condo or a coastal home?
Coastal homes on a wood subfloor, yes, with acclimation, expansion gaps and often narrower boards in the most exposed rooms. Upper-floor condos, usually no for solid nail-down: the subfloor is concrete and the HOA typically requires a tested sound rating and written approval. An engineered floor over an approved acoustic underlayment is the common answer there.
Planning information, not a quote or an inventory list. Prices are set in a written estimate after a site visit. Last reviewed October 2026.
- Family Interiors, cost to install hardwood floors in San Diego (January 2026)
- GreatBuildz, flooring cost in Southern California (October 2026)
- Homeyou, hardwood flooring installation costs in San Diego, 1,282 sq ft model (September 2026)
- Angi, new floor cost for Los Angeles, nearest metro with published data (2026)
- King Remodeling, hardwood floor refinishing cost and process in San Diego (May 2026)
- Bona Traffic HD technical data sheet, US (May 2026)
- CSLB, Check a License (verify C-15 #1002910 and B #970145)
